NS500 Profibus

NS500 Profibus - YAI

Configurable Amplifier, Profibus

The NS500 Profibus is a legacy product and no longer promoted in the Americas. (The retrofit/upgrade to the NS300 is the MP2600iec single axis control.) The NS500 Profibus series was a configurable indexer that attached to the side of any Sigma II amplifier from 30 watts to 55kW and accepts Profibus commands from Profibus masters. The open architecture and modular hardware provide the most flexibe soltion or indexing applications.

User Manual

TemplateWeb

Support
- Available Services
- FAQs
Documents
- Manuals

Support

Documents

Manuals

Support

Documents

FAQs

Sort by :

Expand All

Didn't find what you were looking for? Try solutioncenter.yaskawa.com

Showing 11 to 15 of 16 entries.

Question	Posted Date
How is following error (position error) configured when using an NS-300 or NS-500? Posted Date: 07/13/2004 Answer: Pn505 (Overflow Level) in the SGDH ServoPack sets the maximum allowed position error (the following error limit). If the position error ever exceeds this value, the SGDH will fault with alarm A.D0. The units for Pn505 are 256 Reference Units [256 R.U.]. To set Pn505, convert the maximum position error desired to R.U. and divide by 256, rounding to the nearest integer Example: The reference unit (R.U.) has been set to 0.001mm and the user desires a max following error of 10mm. 10mm = 10,000 R.U. Pn505 = 10,000 R.U./256 = 39 [256 R.U.] (rounded) The R.U. represents the positioning resolution of the controller; the distance the machine moves when 1 pulse is received from the controller. The R.U. is set based on the ratio of two parameters that define the number of controller pulses and encoder counts that represent the same distance. The parameters used depend on the module attached. SGDH: Pn202 and Pn203 (SGDH in position mode, receiving pulse train from external controller) NS600: Pn202 and Pn203 NS300: Pn810 and Pn811 NS500: Pn810 and Pn811 Pn505 should be set after final tuning to 2 or 3 times the normally expected maximum position error. Product Group/Line: Controllers, NS300 DeviceNet, NS500 Profibus Topic/Sub Topic: Ask a Technical Question, Applications, Hardware, Operation, Programming, Troubleshooting Document Number: MTN-5UDT6W Published Date: 07/13/2004 Share \| Rate Rate this article :	07/13/2004
How can the NS-500 (Profibus Indexer) parameters be reset to factory defaults? Posted Date: 08/21/2002 Answer: Turn off the power to the unit and disconnect the Profibus connector. Record current settings of rotary switches. Set both rotary switches to (F). Apply control power, the Err LED will be solid red, the Comm LED will alternate red/green. Wait approximately 10 seconds. Reset is now complete. (Note: this procedure only resets option module parameters to default. If desired, user must reset SGDH parameters separately; Fn5 on amplifier). Turn off the power and set the rotary switches to the original settings. Replace Profibus connector. Product Group/Line: Controllers, NS500 Profibus Topic/Sub Topic: Ask a Technical Question, Programming, Start Up - Installation Document Number: MMIR-5D8JCT Published Date: 08/21/2002 Share \| Rate Rate this article :	08/21/2002
How can NS300 & NS500 be reinitialized to factory default? Posted Date: 09/03/2004 Answer: The following procedure re-initializes NS300 and NS500 parameters to factory defaults: 1. Turn off power to module while it is attached to SGDH drive. 2a. For NS300, set rotary switches X10, X1, and DR to 7. 2b. For NS500 set rotary switches X10 and X1 to F. 3. Turn on power and wait for 10sec. 4. Turn off power and set the rotary switches back to the application settings. Product Group/Line: Controllers, NS300 DeviceNet, NS500 Profibus Topic/Sub Topic: Ask a Technical Question, Instructions Document Number: MTN-5WKNG7 Published Date: 09/03/2004 Share \| Rate Rate this article :	09/03/2004
Does the JUSP-NS500 Profibus Network Indexing module have a GSD file? Posted Date: 06/24/2013 Answer: Yes, it is also posted on the Profibus International Web site. Please see the attached link. http://www.profibus.com/member/337/products/10558/fertig.html# Attachments: 2KB Product Group/Line: Controllers, NS500 Profibus Topic/Sub Topic: Ask a Technical Question, Network Communications, Start Up - Installation Document Number: BFAR-5CKNV7 Published Date: 06/24/2013 Share \| Rate Rate this article :	06/24/2013
Can the SGDH encoder output be used when an NS card is attached? Posted Date: 09/21/2004 Answer: Yes, the SGDH encoder output is available even with the NS300, NS500, or NS600 attached to the drive. The encoder output signals A, B, and C are provided in the CN1 connector on pins 33/34, 35/36, and 19/20 respectively. (See the diagram in the attached .JPG file). The outputs can be wired as a line-driver, open-collector or photo-couple output circuit. For more details on the wiring refer to section 3.4.4 of the Sigma II Series Servo System User Manual. Attachments: 13KB Product Group/Line: Controllers, Servo Products, NS300 DeviceNet, NS500 Profibus, SGDH Sigma II Topic/Sub Topic: Ask a Technical Question, Procedure - Policy Document Number: MTN-5WKTEX Published Date: 09/21/2004 Share \| Rate Rate this article :	09/21/2004

Showing 11 to 15 of 16 entries.

SAFETY PRECAUTIONS AND INSTRUCTIONS FOR USE OF FAQ INFORMATION!

Please read and understand the product instruction manual before installing, servicing or operating Yaskawa products. FAQ content and illustrations are provided as technical advice to augment the information in manual, not supersede it. It is not possible to give detailed instructions for all types of installation or support activities. The information described in the FAQs are subject to change without notice to improve the product or FAQ. Yaskawa assumes no responsibility for errors or omissions or damages resulting from the use of the information contained in any FAQ. All warnings, cautions and product instruction for product use must be followed. Installation, operation and maintenance should be carried out by qualified personnel. Failure to observe these and other precautions highlighted in the product manuals will expose the user to high voltages resulting in, serious injury or death. Qualified personnel are defined as individuals who are familiar with the installation, starting, operation and maintenance of Yaskawa products of the type described and have proper qualifications to perform the work.

Node: dxpprd01:8080

Rating

Rate

SiteSearch

Yaskawa Main Navigation

NS500 Profibus

EditContent

Navigation Menu

NS500 Profibus

NS500 Profibus

NS500 Profibus - YAI

Configurable Amplifier, Profibus

TemplateWeb

Support

Documents

FAQs

SAFETY PRECAUTIONS AND INSTRUCTIONS FOR USE OF FAQ INFORMATION!

Rating

SiteSearch

Americas

Europe/Africa/Middle East

Japan/Asia/Pacific Rim

SiteSearch

NS500 Profibus

Breadcrumb

Navigation Menu

NS500 Profibus

NS500 Profibus

NS500 Profibus - YAI

Configurable Amplifier, Profibus

TemplateWeb

Support

Documents

Support

Documents

FAQs

SAFETY PRECAUTIONS AND INSTRUCTIONS FOR USE OF FAQ INFORMATION!

Rating

SiteSearch