SMC-3010 LEGEND-MC

FAQs

Sort by :

Didn't find what you were looking for? Try

Showing 201 - 220 of 1,000 results.

	Question	Posted Date
	What is the maximum sample rate used in the trending graphic on current Drivewizard software? Posted Date: 12/10/2013 Answer: The sample rate is dependent on type of communication connection and amount of signals sampled. Communication Connection: Serial 50 samples/sec EtherNet 150 samples/sec USB 200 samples/sec Signals Sampled: 1 signal -> 200 samples/sec 2 signals -> 100 samples/sec 4 signals -> 50 samples/sec Product Group/Line: Inverter Drives, DriveWizard HVAC, DriveWizard Industrial, DriveWizard iQpump, DriveWizard MV Topic/Sub Topic: Ask a Technical Question, Drive Wizard, Software Document Number: DRV-9DSN3D Published Date: 12/10/2013 Share \| Rate Rate this article :	12/10/2013
	What is the maximum output frequency of the GA500? Posted Date: 09/27/2019 Answer: The GA500 is capable of 590 Hz output. Please contact us if you have an application requiring greater than 590 HZ. Product Group/Line: Inverter Drives, GA500 Drive Topic/Sub Topic: Ask a Technical Question, Product Launch, Specifications Document Number: INV-5ILEAE Published Date: 09/27/2019 Share \| Rate Rate this article :	09/27/2019
	What is the maximum output frequency of the FP605? Posted Date: 03/30/2022 Answer: The FP605 is capable of 400 Hz output in V/f control and PM open loop vector control (OLV/PM). EZ open loop vector (EZOLV) will output up to 120 Hz. Product Group/Line: Inverter Drives, FP605 Topic/Sub Topic: Ask a Technical Question, Product Launch, Specifications Document Number: INV-I6TX5Y Published Date: 03/30/2022 Share \| Rate Rate this article :	03/30/2022
	What is the maximum number of cam data points that can be stored in a cam table? Posted Date: 07/13/2004 Answer: The Cam Tool software allows a maximum size of 4096 calculated data points for any given cam table. However, there are a total of 32768 16-bit words available in the 'C' registers and 'M' registers of the MP900 series controllers. Cam data are typically stored as long integer numbers (which are 32-bit words). Therefore it takes 2 words for each master or slave position. It takes 4 words to make a single master-slave pair (a single point on the cam table). Dividing 32768 by 4 yields 8191 position pairs that can be stored in a single cam table. (Because 2 words are used as the table header that defines the number of cam points in the table.) If an application requires multiple cam tables that would exceed the memory available, the cam table can be calculated from within the application program or downloaded from an HMI or PC. Product Group/Line: Controllers, MotionWorks Plus Software, MP940 Machine Controller Topic/Sub Topic: Ask a Technical Question, Programming, Specifications Document Number: MNEN-5CJMM4 Published Date: 07/13/2004 Share \| Rate Rate this article :	07/13/2004
	What is the maximum frequency limitation of the pulse input? Posted Date: 07/27/2007 Answer: 33 kHz. Product Group/Line: Inverter Drives, V1000 Drive Topic/Sub Topic: Ask a Technical Question, Specifications Document Number: DRV-75FSHX Published Date: 07/27/2007 Share \| Rate Rate this article :	07/27/2007
	What is the maximum connection distance of the Bluetooth keypad? Posted Date: 09/26/2019 Answer: You can connect via Bluetooth up to 10 m (33 ft) in free air. Any obstructions can reduce this distance. Product Group/Line: Inverter Drives, GA500 Drive, GA800 Drive, FP605 Topic/Sub Topic: Ask a Technical Question, Product Launch, Keypad-Operator Document Number: INV-0V8RZ8 Published Date: 09/26/2019 Share \| Rate Rate this article :	09/26/2019
	What is the life expectancy of a Sigma-5 motor when operating above 40 degrees Celsius (104 F)? Posted Date: 10/18/2010 Answer: The Sigma-5 motor's class F insulation system is rated at 155 degrees Celsius (311 F) maximum internal operating temperature. Every 10 degree C increase of actual temperature above this maximum specification will decrease the life of the insulation system by 50%. The internal temperature of a motor producing rated torque, operating at or below an ambient temperature of 40 degrees Celsius, and mounted to the recommended heat sink should not normally exceed this 155 degrees Celsius limit. Within the rated operating conditions, Yaskawa America Inc. recommends that the bearings be serviced every 20,000 hours. If the ambient temperature exceeds 40 degrees Celsius, the usable life of the bearings and the motor can be decreased but there is no other information available on the bearing life degradation in elevated temperature conditions. The recommended service schedule can be found in the Safety Precaution pamphlet manual that is shipped with every motor ( Manual No. C230200 00B). Please see the attached document for other safety precautions and service schedules. Attachments: 253KB Product Group/Line: Servo Products, SGMAV Sigma-5, SGMGV Sigma-5, SGMJV Sigma-5, SGMSV Sigma-5, SGDV Analog, SGDV EtherCAT, SGDV Indexer, SGDV MECHATROLINK-II, SGDV MECHATROLINK-III, SGDV MP2600iec, SGDV SigmaLogic Topic/Sub Topic: Ask a Technical Question, Environment, Hardware, Operation, Quality, Repair, Specifications, Start Up - Installation, Troubleshooting, Warranty Document Number: MTN-888Q64 Published Date: 10/18/2010 Share \| Rate Rate this article :	10/18/2010
	What is the latest driver for the EXOR HMI connected to an SMC controller, and does it provide hardware handshaking? Posted Date: 06/24/2013 Answer: The latest driver is Galil/Yaskawa 3.09 / 5.04 (see attached UPLC82.DLL). This driver was created August 8, 2002 and allows the programmer to select hardware handshaking ("Use RTS/CTS") from the controller setup screen. This is shown in the first screen capture of Designer Software below. This check box allows compatibility with previous versions of programs (previous version drivers do not use hardware handshaking - See FAQ # MNEN-5CJMH8). Hardware handshaking will enhance communication robustness. This new driver also implements a different method of obtaining controller variable values that the previous driver, further enhancing the relaibility of the system. NOTE: To use hardware handshaking, a new communication cable will need to be wired. New Driver Installation Instructions: Note: When changing to a new driver, the filename will be the same, but the verison number changes. 1) From the C:\Designer directory, make a back-up of the existing UPLC82.DLL driver. 2) Copy the new driver file attached below to that directory to replace the old driver 3) Launch Designer programming software 4) From the Project/Change Controller Driver menu, click on the "Find All" button. This will refresh the driver selection screen. 5) Verify that the Galil/Yaskawa driver shows the latest version stated above. 6) If a project currently exists in the HMI Panel, it will be necessary to delete the old driver protocol from the HMI panel. This function is under TRANSFER>OPTIONS>ADVANCED OPTIONS>ERASE PROTOCOL, or to reset and clear the memory. Attached Files: UPLC82.zip - Galil/Yaskawa driver version 3.09/5.04 EXOR HHS Pin Diagram.xls - Hardware handshaking RS-232 pin to pin diagram Ca036-3.doc - EXOR document showing cable diagram KHUL-5D9JPB.jpg - image example of setup and installed drivers screens Attachments: 60KB 14KB 78KB 45KB Product Group/Line: Controllers, SMC-3010 LEGEND-MC Topic/Sub Topic: Ask a Technical Question, Integration, Programming, Start Up - Installation, Wiring Document Number: KHUL-5D9JPB Published Date: 06/24/2013 Share \| Rate Rate this article :	06/24/2013
	What is the keying of the SGMGV & SGMSV motors, and what is the keying of the SGMGV & SGMSV Yaskawa preassembled right-angle cables for motor power, brake, fan, and encoder? Posted Date: 03/13/2014 Answer: 1. The keying on the motors is visible on the .dxf CAD drawings on Yaskawa.com. (Example: Document 900-032-155 contains the .dxf for SGMSV-70ADA61). 2. They keying of the motor power, brake, and fan cables are on the cable outline drawings on Yaskawa.com (Documents: UDA00629, UDA00641, UDA00642, UDA00643, UDA00644, UDA00645, UDA00646). 3. The keying of the encoder cable is shown in the attached image. If any other keying is desired, contact your Yaskawa sales representative, or procure connector kits from Yaskawa to custom build the cables. Attachments: 48KB Product Group/Line: Servo Products, SGMGV Sigma-5, SGMSV Sigma-5 Topic/Sub Topic: Ask a Technical Question, Specifications Document Number: MTN-9GRJTZ Published Date: 03/13/2014 Share \| Rate Rate this article :	03/13/2014
	What is the inrush current of an SGDH amplifier? Posted Date: 04/16/2001 Answer: For an SGDH 200VAC up to 400W: Normal conditions: 35A (peak) Normal condition is room temperature (20 - 25C degrees) and after enough cool down time for the in-rush current protection thermister. (This means first time to power on, not frequent power on and off) Thermister resistance at room temperature is 8 ohms. In-rush current = 200 x 1.41 / 8 = 35 A Worst case: Max.190A (peak) I2xT (I squared T) = 30[A2sec] <----- 200W, 400W I2xT (I squared T) = 15[A2sec] <----- 100W The worst case condition is at a temperature 30 degrees C and main power turned on for five seconds, then powered off for 5 seconds, repeated 100 times. Product Group/Line: Servo Products, SGDH Sigma II Topic/Sub Topic: Ask a Technical Question, Specifications, Wiring Document Number: MNEN-5CJMLS Published Date: 04/16/2001 Share \| Rate Rate this article :	04/16/2001
	What is the functional safety rating of the GA500? Posted Date: 09/30/2019 Answer: The GA500 has a safe torque off (STO) circuit that meets SIL3 per IEC 620161 and PLe per ISO 13849-1. Product Group/Line: Inverter Drives, GA500 Drive Topic/Sub Topic: Ask a Technical Question, Product Launch, Protective Features Document Number: INV-V61O2Q Published Date: 09/30/2019 Share \| Rate Rate this article :	09/30/2019
	What is the functional safety rating of the FP605? Posted Date: 03/30/2022 Answer: The FP605 has a safe torque off (STO) circuit providing two safe disable inputs and one EDM output (via multi-function digital output) according to EN ISO 13849-1 (PL e (Cat. 3)), IEC/EN 61508 SIL3. Product Group/Line: Inverter Drives, FP605 Topic/Sub Topic: Ask a Technical Question, Product Launch, Specifications Document Number: INV-QST1BO Published Date: 03/30/2022 Share \| Rate Rate this article :	03/30/2022
	What is the format of the Floating Point data structure in the MP920, MP930, MP940 series products? Posted Date: 07/13/2004 Answer: The Format is "The IEEE standard for floating point, single precision (32-bit) arithmetic" The most significant bit is the sign, while the rest is the data area. This is described very well and in significant detail at the sight below: http://www.psc.edu/general/software/packages/ieee/ieee.html If a programmer specifies a Floating Point number as "MF10000", the data structure in the MP memory is attached in the .PDF file below for reference. Attachments: 14KB Product Group/Line: Controllers, MP920 Machine Controller, MP930 Machine Controller, MP940 Machine Controller Topic/Sub Topic: Ask a Technical Question, Document Clarification, Programming, Specifications Document Number: MNEN-5CJMLA Published Date: 07/13/2004 Share \| Rate Rate this article :	07/13/2004
	What is the factory warranty for Sigma SD? Posted Date: 02/21/2018 Answer: The normal 18-month warranty applies. Extended warranties can be purchased. Product Group/Line: Sigma SD Spindle Drive, Spindle Products, Sigma SD Spindle Motor Topic/Sub Topic: Product Launch, Ask a Technical Question Document Number: SPN-239712 Published Date: 02/21/2018 Share \| Rate Rate this article :	02/21/2018
	What is the difference between Z registers and A registers when used in Function Blocks? Posted Date: 04/30/2002 Answer: Z and A registers are both working registers that are used inside function blocks Z registers are Global Internal Function Block registers consisting of 64 words of shared memory space within the CPU (Internal refers to internal to the function block). These registers can be represented in bit, 16-bit word, long word, and floating point, and are working registers available for use specifically within function blocks. Since they are global, several function blocks have access and can modify the stored value. A registers are Local External Function Block registers (External refers to registers used inside the function block, but register space that is reserved outside of the function block). When a function block is defined, a block of memory is reserved by defining the starting address and the data size. This block of memory can be defined as General Global register space (M registers) or Local Drawing register space (D registers). Example: If a function block is defined at address DA00010, and to utilize 10 registers, then registers DW00010 thru DW00019 should be reserved by the programmer for the use of that specific function block. In this case, AW00000 would be mapped directly to DW00010 each scan. When the function block is being used in a drawing, to monitor an internal working register such as AW00000 in this example one would monitor DW00010. - If D registers are used, then A registers are limited to the D register limit for local drawings - quantity of 16383 per drawing. D registers consume programming memory and expand according to need (limited to programming memory available and number of drawings). - If M registers are used, then A registers are limited to the M register limit globally for the controller - quantity of 32767. M registers have a fixed memory space. For more information refer to the Ladder Users Manual Product Group/Line: Controllers, MotionWorks Software, MP920 Machine Controller, MP930 Machine Controller, MP940 Machine Controller Topic/Sub Topic: Ask a Technical Question, Document Clarification, Programming, Specifications Document Number: MNEN-5CJMLE Published Date: 04/30/2002 Share \| Rate Rate this article :	04/30/2002
	What is the difference between the JVOP-183 and JVOP-183R? (or what is meant by back lit?) Posted Date: 07/09/2013 Answer: JVOP-183 comes standard on the Z1000 drive and bypass. It is back lit. JVOP-183R (R not seen on front but is on back label of key pad) it is not back lit. This is intended for outdoor use to help with glare. It comes with the remote mounting option kit(s) UOP000019 and UOP0000197. Attachments: 122KB Product Group/Line: Inverter Drives, Z1000 Bypass, Z1000 Configured, Z1000 Drive Topic/Sub Topic: Ask a Technical Question, Keypad-Operator Document Number: DRV-99FRQ5 Published Date: 07/09/2013 Share \| Rate Rate this article :	07/09/2013
	What is the difference between the I/O on the Sigma II and the MP940? Do both need to be used? Posted Date: 04/26/2001 Answer: There is a difference between the two I/O ports and in most cases both will be used, and is recommended. The Sigma II I/O (CN1 connector) is mostly dedicated I/O with some user defined I/O. The MP940 (I/O connector) is all user defined. Below is an explanation of the inputs and outputs for each device: I/O (MP940): - 8 digital inputs (programmable, isolated 24VDC) - 1 high speed latch input (for external encoder position latching), DC Voltage: 24, 12, or 5 VDC - 1 external encoder input (must be 5 VDC) - 8 digital outputs (programmable, isolated 24VDC) - 1 Analog Output (+/- 10.75VDC, 16-bit resolution, 328uV/bit) CN1 (Servopack): - 4 digital inputs (programmable, isolated 24VDC) - 1 high speed latch input (for motor encoder position latching, can be used as programmable input if latch is not necessary, 24VDC) - 2 overtravel inputs (can be used as programmable inputs if overtravel switches are not necessary, 24VDC) - 1 analog input (+/- 12VDC, 16-bit resolution) - 3 digital alarm code outputs (open collector) - 1 digital servo alarm output (This output will only indicate Servopack alarms, some MP940 alarms will not activate this output.) - 3 digital semi-programmable outputs (These can be configured for various functions which the Servopack activates. For example, one of these must be used to control the brake if a servomotor with a brake is used. 24VDC) - 1 motor encoder output If the system requires I/O from both the MP940 and the Servopack than two breakout cables will be needed. Yaskawa recommends using the standardized I/O (such as Overtravel, SON, and Brake Control) to maintain consistency and system robustness. Product Group/Line: Controllers, Servo Products, MP940 Machine Controller, SGDH Sigma II Topic/Sub Topic: Ask a Technical Question, Specifications, Start Up - Installation, Wiring Document Number: MNEN-5CJMM2 Published Date: 04/26/2001 Share \| Rate Rate this article :	04/26/2001
	What is the difference between the "I" and "J" extended I/O options for the SMC-2000? Posted Date: 07/13/2004 Answer: With the SMC-2000, both the "I" and the "J" options are extended I/O options that add 40 inputs and 42 outputs to the controller. The difference between the two options is the electrical specifications of the outputs. The "I" option uses "dry contact" outputs. These outputs are capable of switching any voltage up to 200VDC (max 0.5A, 10W). Each group of seven outputs has its own common reference, so multiple voltages can be used. The "J" option uses solid-state output. The outputs are all 24VDC (100mA per point), but because they are solid state, there are no mechanical parts to arc and/or wear out. If a system uses mostly 24VDC outputs (this is very common), Yaskawa recommends the "J" option for it's longer life. If there is only one or two outputs that are higher voltage or AC voltage, it is best to use relays to control these outputs. Both the "I" and "J" options use two 50-pin high-density connectors for wiring. This is the same connector at the I/O connector of an SGDH or SGDB amplifier, so the same terminal block connector can be used. This is part number JUSP-TA50P. Product Group/Line: Controllers, SMC-2000 Topic/Sub Topic: Ask a Technical Question, Options Document Number: MNEN-5CJMPY Published Date: 07/13/2004 Share \| Rate Rate this article :	07/13/2004
	What is the difference between STN and TFT on an LCD HMI? Posted Date: 07/13/2004 Answer: LCD: Abbreviation of liquid crystal display, a type of display used in digital watches, many portable computers, and industrial HMI products. All of the EXOR HMI Products have LCD screens. LCD displays utilize two sheets of polarizing material with a liquid crystal solution between them. An electric current passed through the liquid causes the crystals to align so that light cannot pass through them. Each crystal, therefore, is like a shutter, either allowing light to pass through or blocking the light. Monochrome LCD images usually appear as blue or dark gray images on top of a grayish-white background. Color LCD displays use two basic techniques for producing color: Passive matrix is the less expensive of the two technologies. The other technology, called thin film transistor (TFT) or active-matrix, produces color images that are as sharp as traditional CRT displays, but the technology is expensive. Recent passive-matrix displays using new CSTN and DSTN technologies produce sharp colors rivaling active-matrix displays. Most LCD screens used in notebook computers are backlit to make them easier to read. STN: A technique for improving LCD display screens by twisting light rays. In addition to normal supertwist displays, there also exist double supertwist and triple supertwist displays. In general, the more twists, the higher the contrast. Supertwist displays are also known as supertwist nematic (STN) displays. TFT Abbreviation of thin film transistor, a type of LCD flat-panel display screen, in which each pixel is controlled by from one to four transistors. The TFT technology provides the best resolution of all the flat-panel techniques, but it is also the most expensive. TFT screens are sometimes called active-matrix LCDs Product Group/Line: Controllers, General Controllers Topic/Sub Topic: Ask a Technical Question, Specifications Document Number: MNEN-5CJMEN Published Date: 07/13/2004 Share \| Rate Rate this article :	07/13/2004
	What is the difference between MODBUS and Memobus? Posted Date: 04/26/2001 Answer: The Memobus protocol is almost identical to the Modbus protocol. All of the function code calls are the same. The difference between the two protocols lies in the way the data is organized in the registers. 16-bit words are handled the same in both protocols, but addressing individual bits in a 16-bit word is accomplished differently. 32-bit long integer and floating point numbers are also handled differently by the two protocols. The attached document provides a more in-depth comparison between the two protocols. If a complete specification is needed, it can be obtained by calling Yaskawa at (800) YASKAWA option 42 (Publication: SIE-C815-13.60E). Attachments: 37KB Product Group/Line: Controllers, MP920 Machine Controller, MP930 Machine Controller, MP940 Machine Controller Topic/Sub Topic: Ask a Technical Question, Applications, Document Clarification, Network Communications, Specifications Document Number: MNEN-5CJMLY Published Date: 04/26/2001 Share \| Rate Rate this article :	04/26/2001

Showing 201 - 220 of 1,000 results.

SAFETY PRECAUTIONS AND INSTRUCTIONS FOR USE OF FAQ INFORMATION!

Please read and understand the product instruction manual before installing, servicing or operating Yaskawa products. FAQ content and illustrations are provided as technical advice to augment the information in manual, not supersede it. It is not possible to give detailed instructions for all types of installation or support activities. The information described in the FAQs are subject to change without notice to improve the product or FAQ. Yaskawa assumes no responsibility for errors or omissions or damages resulting from the use of the information contained in any FAQ. All warnings, cautions and product instruction for product use must be followed. Installation, operation and maintenance should be carried out by qualified personnel. Failure to observe these and other precautions highlighted in the product manuals will expose the user to high voltages resulting in, serious injury or death. Qualified personnel are defined as individuals who are familiar with the installation, starting, operation and maintenance of Yaskawa products of the type described and have proper qualifications to perform the work.

Node: lr2

Rate