Support

Frequently Asked Questions

Didn't find what you were looking for? Try
  Question Posted Date

Is there a driver available to communicate between an Exor HMI and a Yaskawa Sigma ServoPack?

07/13/2004

Is there a detailed procedure on how to read/write parameters from/to fieldbus NS-300/500 modules?

06/25/2013

Is there a detailed description of the behavior of the IEC functions when EN / ENO are used?

10/09/2015

Is there a demo program available for the SMC-4000 Demo Hardware Unit?

02/18/2009

Is there a cross reference for Omron/Yaskawa servos?

06/15/2010

Is there a compiled list of Sigma II alarms?

07/13/2004

Is there a communication driver available for the SMC controllers?

06/25/2013

Is the P1000 the same physical size as P7?

06/29/2012

Is the MP-940 capable of operating Yaskawa linear motors?

01/14/2005

Is the J1000 the same physical size as J7?

08/01/2008

Is the J1000 dual rated?

08/01/2008

Is the GA500 conformal coated?

09/30/2019

Is the design life of the V1000 is twice that of the V7

07/27/2007

Is the design life of the J1000 twice that of the J7?

08/01/2008

Is the C-phase marker pulse visible though EtherCAT on the SGDV EtherCAT amplifier?

01/03/2020

Is the Copy function available with the standard LED keypad on the V1000 and V1000-4X drives?

06/21/2010

Is the Copy function available with the standard LED keypad on the J1000 Drive?

08/01/2008

Is the A1000 the same physical size as F7?

01/04/2011

Is the A1000 dual rated?

01/04/2011

Is Sigma Trac II a drop-in replacement for SGT Sigma Trac?

08/23/2019

Is PID available on the J7 Drive?

10/27/2005

Is MotionWorks MPE720 ver 5.13 compatible with Microsoft XP SP2?

07/25/2013

Is it possible to wire an HMI to Multiple NS600 Indexer modules?

11/20/2001

Is it possible to verify if an axis is present on the system via the MotionWorks IEC application program?

10/15/2010

Is it possible to use the second Ethernet port, CN11B, on the MP2600iec as a separate, independent network connection?

03/18/2013

Is it possible to use the Legend amplifiers with an SVA module, and if so, with what control method?

07/25/2005

Is it possible to use auto-tuning without rotating the motor?

07/13/2004

Is it possible to troubleshoot fieldbus modules that won't respond to PLC commands?

09/21/2004

Is it possible to transfer more than the 256 byte maximum Ethernet/IP adaptor assembly instance between an MP2000iec controller and an AB PLC without resorting to multi-plexing data within a single instance?

03/18/2013

Is it possible to transfer cam data from Mircosoft Excel to an MP controller?

10/26/2005

Is it possible to simply control speed in a Sigma II amplifier without a controller?

10/24/2002

Is it possible to set up ASCII text fields in an HMI Recipe to specify recipe name so it can be modified and stored in an MP9** Controller?

11/08/2001

Is it possible to save MW+ scope data for review and distribution?

03/13/2002

Is it possible to run MotionWorks IEC via Remote Desktop?

04/05/2012

Is it possible to route the POT and NOT signals through DeviceNet on an MP940D?

09/05/2001

Is it possible to reset all Sigma II parameters to factory default?

07/13/2004

Is it possible to replace an I/O device with another, but still maintain original variables?

02/06/2009

Is it possible to register and use MotionWorks IEC through a remote desktop?

04/05/2012

Is it possible to Program/Monitor a LEGEND MC remotely via a modem, through an EXOR HMI?

05/01/2002

Is it possible to prevent the momentum of a linear motion system from carrying the table (or carriage) past a limit switch?

05/21/2001

Is it possible to pause motion once started and resume to the same target later?

07/13/2004

Is it possible to Monitor/Program an MP9** Product over a phone line from a remote location?

07/13/2004

Is it possible to launch and run SigmaWin+ from MotionWorks v6?

05/28/2013

Is it possible to isolate or split the encoder output signal from an SGDH PG output?

07/13/2004

Is it possible to import a register tag list into an EXOR HMI product?

10/22/2019

Is it possible to export Modbus tag variables from MotionWorks IEC and import them into Red Lion's Crimson software?

10/22/2019

Is it possible to decode the S-Channel information from an Yaskawa absoute encoder into a usable format?

04/30/2003

Is it possible to cover the blank slots in the MP920 Controller Rack?

07/13/2004

Is it possible to connect Wonderware to a Yaskawa MP920 Machine Controller?

06/19/2013

Is it possible to connect multiple MP940s to one EXOR HMI?

12/21/2011

SAFETY PRECAUTIONS AND INSTRUCTIONS FOR USE OF FAQ INFORMATION!

Please read and understand the product instruction manual before installing, servicing or operating Yaskawa products. FAQ content and illustrations are provided as technical advice to augment the information in manual, not supersede it. It is not possible to give detailed instructions for all types of installation or support activities. The information described in the FAQs are subject to change without notice to improve the product or FAQ. Yaskawa assumes no responsibility for errors or omissions or damages resulting from the use of the information contained in any FAQ. All warnings, cautions and product instruction for product use must be followed. Installation, operation and maintenance should be carried out by qualified personnel. Failure to observe these and other precautions highlighted in the product manuals will expose the user to high voltages resulting in, serious injury or death. Qualified personnel are defined as individuals who are familiar with the installation, starting, operation and maintenance of Yaskawa products of the type described and have proper qualifications to perform the work.