Support

Frequently Asked Questions

Didn't find what you were looking for? Try
  Question Posted Date

CPF10 -- Fault Code Description

11/16/2009

CPF09 -- Fault Code Description

11/16/2009

CPF08 -- Fault Code Description

11/16/2009

CPF07 -- Fault Code Description

11/16/2009

CPF06 with Replacement Control Board

08/28/2012

CPF06 -- Fault Code Description

06/08/2007

CPF05 -- Fault Code Description

06/08/2007

CPF05 -- Fault Code Description

11/16/2009

CPF04 -- Fault Code Description

11/16/2009

CPF04 -- Fault Code Desciption

06/08/2007

CPF02 -- Fault Code Description

11/16/2009

CPF02 -- Fault Code Description

06/08/2007

CPF01 -- Fault Code Description

11/16/2009

CPF01 -- Fault Code Description

06/08/2007

CPF00 -- Fault Code Description

06/20/2013

CF -- Fault Code Description

06/08/2007

Can you use gateway mode with a mix of GA800 and GA500 drives?

09/30/2019

Can you explain the Hand/Auto Mode selection on the Z1000 series?

06/21/2013

Can you do a 5 Axis head with Yaskawa Compass?

05/21/2020

Can you change units from mm/sec to in/sec in Compass?

05/21/2020

Can we replace simple servo applications using existing PM servo motors?

01/04/2011

Can we implement laser parameters in Compass?

05/19/2020

Can we draw part viewing with Compass?

05/21/2020

Can V1000-4X Options be used with V74X?

06/21/2010

Can the value of an internal parameter be used in an expression?

03/22/2001

Can the V7 provide an analog output signal programmed for motor output current?

06/20/2013

Can the V1000 be applied to HVAC applications?

07/27/2007

Can the standard GA800 LCD keypad be used on the GA500?

09/30/2019

Can the speed reference to a V7 Drive be switched 'on the fly' between run and jog?

07/13/2004

Can the SMC-2000 and/ or SMC-3010 be switched into and out of gearing while the motor is moving?

10/12/2001

Can the Sigma SD run a legacy Yaskawa spindle motor?

02/21/2018

Can the Sigma II SGDH Servopack provide analog monitors on the 1CN connector like the Sigma I SGDB Servopack?

07/13/2004

Can the Sigma II absolute encoder data be preserved when the encoder cable is removed?

02/11/2005

Can the SGDH encoder output be used when an NS card is attached?

09/21/2004

Can the SGDG be configured to run with motors equipped with absolute encoders?

09/05/2001

Can the SD run another manufacturer’s spindle motor?

02/21/2018

Can the same hand-held digital operator panel (Yaskawa # JUSP-OP02A-1) be used in conjunction with Sigma II amplifiers as used with the Sigma I?

07/13/2004

Can the PID in the V7 Drive be used for positioning?

10/09/2014

Can the operator on the V7 Drive be removed and remotely mounted?

10/27/2005

Can the NS600 be tested using serial commands sent from a PC?

03/26/2014

Can the MP920 change the parameters in an SGDH amplifier?

08/19/2004

Can the MP2300 control a servo's position with a torque mode amplifier over MechatroLink?

07/25/2005

Can the motor brake output (/BK) on an EtherCAT SERVOPACK be controlled by the EtherCAT Master?

11/03/2017

Can the MotionWorks IEC Pro template project be used for most Compass applications?

05/21/2020

Can the LIO-01/-02/-06 for the MPiec Controller take a single-ended encoder input?

07/08/2013

Can the linear encoder be mounted "backwards" (positive direction of linear encoder opposite to positive direction of linear motor)?

04/28/2003

Can the LEGEND amplifier accept a 5VDC input to enable the motor?

10/31/2002

Can the LCD Operator be used for programming and maintenance of the V1000-4X?

06/21/2010

Can the keypad from J7 Drive be removed and installed at a remote location? If yes what is the part no. of the cable and what is the distance it can support?

06/11/2014

Can the JP and JS commands do more than jump to a specified label?

07/13/2004

SAFETY PRECAUTIONS AND INSTRUCTIONS FOR USE OF FAQ INFORMATION!

Please read and understand the product instruction manual before installing, servicing or operating Yaskawa products. FAQ content and illustrations are provided as technical advice to augment the information in manual, not supersede it. It is not possible to give detailed instructions for all types of installation or support activities. The information described in the FAQs are subject to change without notice to improve the product or FAQ. Yaskawa assumes no responsibility for errors or omissions or damages resulting from the use of the information contained in any FAQ. All warnings, cautions and product instruction for product use must be followed. Installation, operation and maintenance should be carried out by qualified personnel. Failure to observe these and other precautions highlighted in the product manuals will expose the user to high voltages resulting in, serious injury or death. Qualified personnel are defined as individuals who are familiar with the installation, starting, operation and maintenance of Yaskawa products of the type described and have proper qualifications to perform the work.