Support

Frequently Asked Questions

Didn't find what you were looking for? Try
  Question Posted Date

When setting parameter Pn300 (Speed Reference Input Gain) what rated speed should be used for Linear Motor applications?

02/18/2009

When setting parameter Pn300 (Speed Reference Input Gain) what rated speed should be used for Linear Motor applications?

07/13/2004

When running into hardware limits, motion is disabled in both directions. How can the axis be jogged off the limit switch?

07/13/2004

When replacing the motor for the application and the heat sink cooling fans. How do I reset Cumulative Motor Operation Time U1-13 and Heat Sink Cooling Fan Operation Time U1-40?

09/16/2013

When reading 42h it does not match U1-03? Using Ethernet or Modbus protocols.

08/31/2012

When moving away from a overtravel condition, the Sigma V servo system seems to prevent torque or rapidly enable/disable as the axis is moving out of the overtravel region. Can this situation be prevented?

10/06/2011

When is it necessary to connect an external regen resistor to the SGDG LEGEND amplifier?

01/21/2002

When I install my serial communications option board onto the Z1000 drive in the Z1B cabinet, I recieve alarm OFA00. What am I doing wrong?

02/28/2013

When entering Motor Rated Current (parameter E2-01) into an E7 drive, an OPE02 fault appears on the display. What can cause this, and how is the fault cleared?

06/08/2007

When dealing with harmonic noise, which is better-- an AC or a DC reactor?

06/20/2013

When configuring an IP address in the resource settings of MotionWorks IEC, what are the -TO and -P attributes?

11/10/2017

When an MP940 with a 17-bit encoder is being operated, does the encoder resolution need to be reduced?

04/27/2001

What’s the maximum number of axes that could be controlled and configured by a Compass solution?

05/21/2020

What Z1000 enclosure types are available?

11/29/2011

What would cause an "06" communications error code in an HMI when talking to one or more NS600(s)?

11/21/2001

What will happen to the P7?

06/29/2012

What will happen to the E7?

11/29/2011

What will happen if there is only .5'' clearance from either top or bottom of the drive to an enclosure?

03/14/2006

What web browser technology is supported by the MPiec Series Controllers?

01/02/2018

What web browsers are compatible with the MPiec controller's web server?

01/23/2018

What voltage levels will cause an overvoltage or undervoltage alarm?

03/02/2015

What voltage levels will cause an overvoltage or undervoltage alarm?

02/06/2009

What version of Sigma II fimware is required if using an option card such as the MP940?

04/04/2002

What version of Java is required to view the Machine Operations page of an MPiec Controller?

07/04/2013

What type of Errors and Alarms are on the controller?

02/18/2009

What training is available for P1000?

06/29/2012

What training is available for GA800?

01/11/2019

What training is available for A1000?

01/03/2011

What tools are available to help customers convert from P7 to P1000?

06/29/2012

What tools are available to help customers convert from G5 (600V) and F7 to A1000?

01/03/2011

What tools are available to help customers convert from F7 and A1000 to GA800?

01/11/2019

What tools are available to help customers convert from E7 to Z1000?

11/29/2011

Whats the maximum number of User Function blocks that can be used in the MP900 series controllers?

03/06/2002

What steps are required to upgrade Sigma products to Sigma II?

04/10/2006

What steps are required to communicate to a LEGEND-MC from a laptop PC via Ethernet?

07/13/2004

What steps are necessary to connect a Yaskawa V1000 to an MPiec series controller over ethernet?

12/12/2016

What software tools are available to save F7 drive parameter settings to a PC file?

09/13/2012

What should the inertia ratio parameter, Pn103, be set to in the Sigma II amplifier when the inertia ratio is not known?

06/24/2013

What should be done with the CN8 connection when using the Safety Option Module (SGDV-OSA01A)?

01/30/2020

What settings are needed to configure the E7 Bypass for serial communication control in AUTO mode and keypad speed control in HAND mode?

06/11/2014

What screen resolutions are supported by Compass?

05/21/2020

What screen resolutions are compatible with Compass?

04/28/2020

What peripheral components are required for use with the R1000 for UL?

07/15/2015

What peripheral components are required for use with the D1000 for UL?

07/15/2015

What parameter sets the maximum output frequency for V7 series drives?

06/20/2013

What parameter must be set when using a DC power supply for a SERVOPACK’s main circuit power supply?

02/26/2019

What P1000 enclosure types are available?

06/29/2012

What options are available to stop the motor using EtherCAT commands?

12/22/2015

What options are available to limit torque on the SGDV CANopen over EtherCAT SERVOPACK?

07/15/2015

What new features does the Z1000 offer beyond those of the E7?

11/29/2011

SAFETY PRECAUTIONS AND INSTRUCTIONS FOR USE OF FAQ INFORMATION!

Please read and understand the product instruction manual before installing, servicing or operating Yaskawa products. FAQ content and illustrations are provided as technical advice to augment the information in manual, not supersede it. It is not possible to give detailed instructions for all types of installation or support activities. The information described in the FAQs are subject to change without notice to improve the product or FAQ. Yaskawa assumes no responsibility for errors or omissions or damages resulting from the use of the information contained in any FAQ. All warnings, cautions and product instruction for product use must be followed. Installation, operation and maintenance should be carried out by qualified personnel. Failure to observe these and other precautions highlighted in the product manuals will expose the user to high voltages resulting in, serious injury or death. Qualified personnel are defined as individuals who are familiar with the installation, starting, operation and maintenance of Yaskawa products of the type described and have proper qualifications to perform the work.