SGLF Series

SGLF Series - Sigma-5 - YAIMOB

Iron-core coil and magnet track components

Iron core FW linear motors are composed of moving coils with laminated iron-core and single sided stationary magnet tracks. The moving coil of the FW linear motor is composed of laminated iron core and prewound coil bobbins inserted into the slots located on the laminated iron cores. The entire coil unit is permanently encapsulated in a thermally conductive resin body to give structural rigidity. The magnet track of the FW is made of a row of rare earth magnets accurately placed on one side of the nickelized steel carrier plate. Stainless steel magnet covers guard against minor accidental damage to the magnets.

TemplateWeb

FAQs

Sort by :

Expand All

Didn't find what you were looking for? Try solutioncenter.yaskawa.com

Showing 1 to 16 of 16 entries.

Question	Posted Date
Will non-Renishaw or non-Heidenhain encoders work with Yaskawa serial converters? Posted Date: 03/17/2016 Answer: Please see attached document for details. Attachments: 192KB Product Group/Line: SGDV Analog, Servo Products, SGDV EtherCAT, SGDV Indexer, SGDV MECHATROLINK-II, SGDV MECHATROLINK-III, SGDV MP2600iec, SGDV SigmaLogic, SGLT Series, SGLG Series, SGLF Series Topic/Sub Topic: Wiring, Ask a Technical Question Document Number: SRV-K07R01 Published Date: 03/17/2016	03/17/2016
When setting parameter Pn300 (Speed Reference Input Gain) what rated speed should be used for Linear Motor applications? Posted Date: 02/18/2009 Answer: The configuration of Parameter Pn300 is the same for Linear Motor applications as it is for Rotary Motor applications. The motor speed is controlled in proportion to the input voltage between V-REF (CN1-5) and SG (CN1-6). This is depicted in the attached .PDF File. For further information regarding adjustment of parameter Pn300, refer to the Sigma II Series SGDH User's Manual Supplement for Linear Sigma Series [YEA-SIA-S800-39.21] section 4.7 Operating Using Speed Control with Analog Reference. Attachments: 22KB Product Group/Line: Servo Products, SGDH Sigma II, SGLF Series, SGLG Series, SGLT Series Topic/Sub Topic: Ask a Technical Question, Programming, Start Up - Installation Document Number: MMIR-5CM5KN Published Date: 02/18/2009	02/18/2009
What is the warranty determination for new product? Posted Date: 05/22/2014 Answer: 1. Yaskawa America, Inc (YAI, Drives & Motion Division (hereinafter D&M), warrants at the time of shipment, new and unused product sold by D&M shall be free from defects in materials and workmanship. D&M warrants that for a period of one (1) year from the date the product is first used by Buyer, or 18 months from the date of shipment, whichever occurs first, if any product or part is found by D&M to be defective, D&M will, at its sole discretion and as Buyer's exclusive remedy, either repair, replace or return the purchase price paid to D&M; provided that the subject product is used under normal conditions for which it was designed and installed, operated and maintained in accordance with D&M's instructions and in accordance with generally accepted industrial practices. Products repaired or replaced during the warranty period shall be covered by the foregoing warranty for the remainder of the original warranty period or ninety (90) days from date of the repair or shipment of the replacement, whichever is longer. D&M warrants, for a period of ninety (90) days, that services shall be performed in a workmanlike manner. Buyer's sole remedy for a breach of this service warranty is limited to further service or a refund or credit of amounts paid by Buyer, at Seller's option. 2. D&M's warranty obligation shall be conditioned upon receipt by D&M of written notice of any alleged defects within sixty (60) days after discovery. D&M will not be responsible for unauthorized repairs to any products, even if defective. D&M shall not be responsible for any products which have been altered, abused, misused, or improperly installed or repaired, or for any loss, damage, defect, claim or non-performance resulting from or attributable to Buyer's specifications. D&M does not guarantee production rates or the quality of goods made using D&M's products or services, nor shall any longer warranty periods apply, except as agreed in writing signed by an authorized D&M representative. 3. Where Buyer orders non-stock products or parts manufactured by a third-party, D&M will, to the extent permitted, pass through to Buyer any warranty of the manufacturer. As to such items, Buyer's sole remedy for breach of warranty shall be the remedy offered by and available from the manufacturer, if any. 4. D&M's warranty herein is in lieu of and excludes all other warranties of D&M and any parent or affiliated companies of D&M. D&M disclaims all other warranties, whether express, implied or statutory, including, but not limited to, any implied warranties of merchantability and/or fitness for a particular purpose or use. 5. Under no circumstances shall D&M, or any parent or affiliated company of D&M, be liable to buyer or any entity for any special, indirect or consequential damages, whether arising from breach of contract, tort, negligence, misrepresentation, strict liability or otherwise, including for lost profits, impairment of goods, work stoppage or otherwise, in any way arising out of or related to products or services supplied by D&M or any transaction to which these standard terms apply. The maximum liability of D&M, including, but not limited to, with respect to the design, manufacture, sale, delivery, resale, inspection, assembly, installation, testing, repair, replacement, maintenance or use of any product or the performance of any service, shall not exceed the purchase price paid to D&M. Product Group/Line: Inverter Drives, Controllers, Servo Products, General Controllers, General Inverter Drives, General Servo, MP2300Siec, MP2310iec, MP2600iec, MP2200, MP2300, MP3200iec, MP3300iec, Yaskawa Remote IO Modules, A1000 Configured, A1000 Drive, D1000 Regenerative Converter, G7 Drive, iQpump Micro, iQpump Micro Configured, iQpump1000, iQpump1000 Bypass, iQpump1000 Configured, J1000 Drive, L1000A Drive, L1000E Drive, MV1000 Drive, P1000 Drive, R1000 Regenerative Unit, U1000 Industrial Matrix Drive, U1000 Oil and Gas MATRIX Drive, V1000 Drive, V1000-4X Drive, Z1000 Bypass, Z1000 Configured, Z1000 Drive, Z1000 Redundant, Z1000U Matrix Bypass, Z1000U Matrix Configured, Z1000U Matrix Drive, SGDV Analog, SGDV EtherCAT, SGDV MECHATROLINK-II, SGDV MECHATROLINK-III, SGDV MP2600iec, SGDV SigmaLogic, SGLF Series, SGLG Series, SGLT Series, SGMAV Sigma-5, SGMCS Direct Drive, SGMGV Sigma-5, SGMJV Sigma-5, SGMMV Sigma-5 Mini, SGMPH Sigma II, SGMSV Sigma-5, SGMVV Sigma-5, SGT Sigma Trac, SJDE Junma, SJME Junma, SLIO Modules, SGM7E Direct Drive, SGM7D Direct Drive, SGM7F Direct Drive Topic/Sub Topic: Ask a Technical Question, Warranty Document Number: DRV-9BJPJ9 Published Date: 05/22/2014	05/22/2014
What is the maximum setting for parameter Pn281 (PG Divider) given the linear scale pitch and maximum speed of the linear motor? Posted Date: 07/13/2004 Answer: When using linear motors, the maximum encoder frequency is 12.8MHz. The maximum setting of parameter Pn281 (Encoder Resolution) is dependent upon parameter Pn280 (Linear Scale Pitch) and Pn384 (Peak Motor Speed.) Attached to this document (.JPG file) is a table showing the maximum setting for Pn281 for specific Pn280 and Pn384 settings. Monitor Un010 can also be used to monitor the following: A) The maximum value of Pn281 (Encoder Resolution) for a given Pn280 (Linear Scale Pitch) and Pn384 (Peak Motor Speed) (default monitor.) B) The maximum value of Pn384 (Peak Motor Speed) for a given Pn280 (Linear Scale Pitch) and Pn281 (Encoder Resolution.) Set Pn080.3=1 to enable this monitor. Attachments: 33KB Product Group/Line: Servo Products, SGDH Sigma II, SGLF Series, SGLG Series, SGLT Series Topic/Sub Topic: Ask a Technical Question, Specifications, Start Up - Installation Document Number: PZAC-5MXTZF Published Date: 07/13/2004	07/13/2004
What is the air gap requirement for Yaskawa's Linear Motors? Posted Date: 07/13/2004 Answer: The air gap between the Linear Motor Coil and the Magnet track is as follows: SGLGW40 & SGLGW60 Coreless Series: 0.8 mm +/- 0.3 mm SGLFW Iron Core Series: 0.8 mm +/- 0.3 mm SGLTW20 & SGLTW35 Iron Core Series: 0.8 mm +/- 0.3 mm SGLTW40 & SGLTW80 Iron Core Series: 1.2 mm +/- 0.3 mm. The air gap or the air gap tolerance is a fixed value and is solely the function of the mechanical structure i.e. bearings and frame (not a function of the attraction force between the magnet track and the motor coil). The attaction force will change if the air gap is more or less than that which is optimum. Product Group/Line: Servo Products, SGLF Series, SGLG Series, SGLT Series Topic/Sub Topic: Ask a Technical Question, Integration, Specifications Document Number: MNEN-5CJMSS Published Date: 07/13/2004	07/13/2004
What is California's Proposition 65? Posted Date: 06/01/2020 Answer: California Proposition 65 is a standalone program that affects commercial goods sold in the state of CA. This was enacted in 1986 as "The safe Drinking Water and Toxic Enforcement Act of 1986". Businesses, including manufacturers, producers, packagers, importers, suppliers and distributors, are required to provide warnings required under the California Code of Regulations (the “Code”) if their products or facilities can expose consumers or workers to a listed chemical above identified threshold levels, known to the state of California to cause cancer or reproductive harm. The chemical list contains more than 900 substances, and this list is updated every year. Read Full Policy Product Group/Line: Controllers, Inverter Drives, Servo Products, Spindle Products, General Servo, General Spindle, General Controllers, MP3300iec, Sigma-7Siec, MP3300iec-RBT, Panel PC, smartPanel, SLIO Modules, Yaskawa Remote IO Modules, MP3200, General Inverter Drives, GA800 Drive, GA800 Configured, A1000 Drive, A1000 Configured, U1000 Industrial Matrix Drive, G7 Drive, GA500 Drive, V1000 Drive, V1000-4X Drive, J1000 Drive, P1000 Drive, P1000 Bypass, P1000 Configured, Z1000 Drive, Z1000 Bypass, Z1000 Configured, Z1000 Redundant, Z1000U Matrix Drive, Z1000U Matrix Bypass, Z1000U Matrix Configured, iQpump1000, iQpump1000 Bypass, iQpump1000 Configured, iQpump Micro, iQpump Micro Configured, U1000 iQpump, U1000 iQpump Configured, L1000A Drive, L1000E Drive, D1000 Regenerative Converter, R1000 Regenerative Unit, MV1000 Drive, MV1000 NEMA 3R, SGD7W Mechatrolink-III, SGD7S Mechatrolink-III, SGD7W EtherCAT, SGD7S EtherCAT, SGD7S Analog, SGD7S Sigma-7Siec, SGD7S MP2600iec, SigmaLogic7 Compact, SigmaLogic7 Modbus, SGM7J Sigma-7, SGM7A Sigma-7, SGM7P Sigma-7, SGM7G Sigma-7, S7J Gear Motors, S7A Gear Motors, S7P Gear Motors, S7G Gear Motors, SGM7F Direct Drive, SGM7D Direct Drive, SGMCS Direct Drive, SGLF2 Series, SGLG Series, SGLT Series, Sigma Trac II, SGDV MECHATROLINK-III, SGDV MECHATROLINK-II, SGDV EtherCAT, SGDV Analog, SGDV SigmaLogic, SGDV MP2600iec, SGMMV Sigma-5 Mini, SGMJV Sigma-5, SGMAV Sigma-5, SGMGV Sigma-5, SGMSV Sigma-5, SGMVV Sigma-5, SGLF Series, Sigma SD Spindle Drive, Sigma SD Spindle Motor, HV600 Drive, HV600 Enclosed Bypass, HV600 Enclosed Configured, HV600 Narrow Bypass, HV600 Narrow Configured, FP605, SGM7E Direct Drive Topic/Sub Topic: Ask a Technical Question, Environment Document Number: CNT-INV-SRV-SPN-322SVA Published Date: 06/01/2020	06/01/2020
What are the minimum settings required to start-up a LEGEND SGDG type servo amplifier for use with a linear motor? Posted Date: 07/13/2004 Answer: See the attached .PDF file for information and tables regarding the SW2 Linear Scale Pitch setting Attachments: 19KB Product Group/Line: Servo Products, SGDG LEGEND, SGLF Series, SGLG Series, SGLT Series Topic/Sub Topic: Ask a Technical Question, Programming, Start Up - Installation Document Number: PZAC-5PBSRG Published Date: 07/13/2004	07/13/2004
What are the minimum parameters required to start-up a Sigma II SGDH type servo amplifier for use with a linear motor? Posted Date: 07/25/2005 Answer: Pn000.1 Control Method Selection Set the amplifier to the correct control method (force control, speed control, position control, etc.) Note: Set Pn000.1=2 for force control Pn280 Linear Scale Pitch [microns] Set the linear scale pitch parameter to the scale pitch (i.e. grating pitch or signal period) of the linear encoder. The linear encoder must output a 1Vpp analog sin/cos waveform. The default setting of Pn280 is 0. Alarm A.08 (linear encoder scale pitch setting error) will occur at power-up if this parameter is left at setting 0. Pn281 Encoder Output Resolution [Pulse/Scale Pitch (Pn280)] - Force/Speed Control This parameter is used to scale the encoder output resolution from the servo amplifier. The factory setting is 20; therefore, for a linear encoder with a scale pitch of 40 micron (Pn280=40), the encoder output resolution is 20 pulses (Pn281) divided by 40 micron (Pn280), or 1 pulse per 2 microns. Pn202 Electronic Gear Ratio (Numerator) - Position Control The Electronic Gear Ratio is used to scale the input position reference. See the following FAQ: How are the Electronic Gear Ratio parameters, Pn202 and Pn203, set for linear motors? Pn203 Electronic Gear Ratio (Denominator) - Position Control The Electron Gear Ratio is used to scale the input position reference. See the following FAQ: How are the Electronic Gear Ratio parameters, Pn202 and Pn203, set for linear motors? Pn483 Forward Thrust Limit [%] To prevent danger during motor setup, the factory setting of the forward force limit is set low to 30%. Verify that the linear motor is working properly before increasing this value. Pn484 Reverse Thrust Limit To prevent danger during motor setup, the factory setting of the reverse force limit is set low to 30%. Verify that the linear motor is working properly before increasing this value. Pn50A.3 P-OT Input Signal Mapping The positive overtravel input is factory set to prohibit forward motion. Connect a limit switch to the P-OT input to prevent forward motion beyond the allowable range. The P-OT input can also be disabled to always allow forward motion by setting Pn50A.3 equal to 8. Pn50B.0 N-OT Input Signal Mapping The negative overtravel input is factory set to prohibit reverse motion. Connect a limit switch to the N-OT input to prevent reverse motion beyond the allowable range. The N-OT input can also be disabled to always allow reverse motion by setting Pn50B.0 equal to 8. Product Group/Line: Servo Products, SGDH Sigma II, SGLF Series, SGLG Series, SGLT Series Topic/Sub Topic: Ask a Technical Question, Procedure - Policy, Programming, Start Up - Installation Document Number: PZAC-5PBLP6 Published Date: 07/25/2005	07/25/2005
On a linear motor x-x'-y gantry system, what is the best method to control the two x-axes? Posted Date: 06/06/2003 Answer: The preferred method is to set-up a master/slave relationship using two axes of a motion controller. The motion controller must monitor the linear encoder feedback from both the x and x'. The x' axis must track the position of the x axis. Another alternative is to set-up a master/slave relationship using only one axis of a motion controller. The motion controller would monitor the linear encoder feedback from the x axis and command the x' axis. The x' axis would follow the encoder output directly from the x axis encoder output. Caution should be taken when implementing this method, since each amplifier operates in a different control method and different loop updates may exist. The following example lists the necessary SGDH amplifier parameter settings for a linear motor master/slave application (assuming a linear encoder grating pitch of 20 microns). Master Axis Parameter Settings: Pn000.1=2 Sets amplifier in Force Control. Pn280=20 Linear encoder grating pitch is 20 micron. Pn281=20 Sets encoder output resolution to 20 micron per 20 pulses (or 1 micron per 1 pulse). Slave Axis Parameter Settings: Pn000.1=1 Sets amplifier in Position Mode. Pn280=20 Linear encoder grating pitch is 20 micron. Pn202=256 Electron gear ratio numerator. Pn203=20 Electronic gear ratio denominator. The electronic gear ratio is used to scale the postion command input. Product Group/Line: Servo Products, SGDH Sigma II, SGLF Series, SGLG Series, SGLT Series Topic/Sub Topic: Ask a Technical Question, Applications, Integration, Start Up - Installation Document Number: PZAC-5N9KGR Published Date: 06/06/2003	06/06/2003
Is there any information that illustrates where linear motor technology has been successfuly applied? Posted Date: 06/16/2010 Answer: Control Design magazine has written an article that highlights Tri-Tech Industries utilization of linear motor technology to increase production and precision of motion control in the Food Industry and compares results to traditional linear motion methods. See attached .PDF file for complete article. Attachments: 129KB Product Group/Line: Servo Products, SGLF Series, SGLG Series, SGLT Series Topic/Sub Topic: Ask a Technical Question, Applications, Document Clarification, Start Up - Installation Document Number: MTN-5S5KNA Published Date: 06/16/2010	06/16/2010
Is there any information available about a free software to use for opening Yaskawa 2D drawings such as dwg and dxf? Posted Date: 05/15/2014 Answer: To open and edit 2D dwg and dxf drawings; use DraftSight which can be downloaded from its website. Search for DraftSight on the web. Product Group/Line: Servo Products, SGDG LEGEND, SGDH Sigma II, SGDS, SGLF Series, SGLG Series, SGLT Series, SGMAH Sigma II, SGMAV Sigma-5, SGMBH Sigma II, SGMCS Direct Drive, SGMGH Sigma II, SGMGV Sigma-5, SGMJV Sigma-5, SGMM Sigma Mini, SGMPH Sigma II, SGMSH Sigma II, SGMSV Sigma-5, SGMUH Sigma II, Sigma FSP, Sigma Trac, SGT Sigma Trac, STF Sigma Trac, SJDE Junma, SJME Junma, Controllers, JAMSC-Network IO, JUSP-FC100 Full Closed IF Unit, MotionWorks IEC, MotionWorks Plus Software, MP2000 Series (MP2300-MP2200), MP2000iec Series, MP2100, MP2200, MP2300, MP2300Siec, MP2310iec, MP2600iec, MP3200, MP3200iec, MP920 Machine Controller, MP930 Machine Controller, MP940 Machine Controller, NS100 Mechatrolink, NS115 Mechatrolink II, NS300 DeviceNet, NS500 Profibus, NS600 Indexer, NT001, SMC-2000, SMC-3010 LEGEND-MC, SMC-4000, YTerm Software, SGDV Analog, SGDV EtherCAT, SGDV Indexer, SGDV MECHATROLINK-II, SGDV MECHATROLINK-III, SGDV MP2600iec, SGDV SigmaLogic, Network-Comm-EtherCAT, Network-Comm-MECHATROLINK-II, Network-Comm-Options, SGM7D Direct Drive, SGM7E Direct Drive, SGM7F Direct Drive Topic/Sub Topic: Ask a Technical Question, Dimensions Document Number: MTN-9G4SB7 Published Date: 05/15/2014	05/15/2014
Is the MP-940 capable of operating Yaskawa linear motors? Posted Date: 01/14/2005 Answer: Yes, it is possible when using MotionWorks. The only difference between using a rotary motor and a linear motor with the MP-940 is to select Linear Type vs Rotary Type in the SVA section of Module Configuration. By doing this, the additional parameters for Linear Motors are displayed in the "ServoPack" tab. There are three, however, that will require immediate attention to allow motion to occur. Please reference the users manuals for information regarding all other parameters. SGDH Parameter Settings: 1) Pn280: Linear Scale Pitch (micrometers), the ServoPack will remain in an alarm state until this is set. 2) Pn483: Forward Force Limit (% of rated), factory default is 30% (for safety), set appropriately for application. 2) Pn484: Reverse Force Limit (% of rated), factory default is 30% (for safety), set appropriately for application. Minimum firmware & software versions required: MP940: B01 or higher SGDH: xx214 or higher MotionWorks: 4.20 or higher Attachments: 61KB Product Group/Line: Controllers, Servo Products, MP940 Machine Controller, SGDH Sigma II, SGLF Series, SGLG Series, SGLT Series Topic/Sub Topic: Ask a Technical Question, Operation, Start Up - Installation Document Number: MNEN-5CJMRC Published Date: 01/14/2005	01/14/2005
How do I run a Yaskawa linear motor without hall sensors? Posted Date: 03/12/2024 Answer: This FAQ describes the required amplifier parameters settings for enabling and operating the polarity detection feature for hall-less operation of Sigma-5 linear motor systems. The polarity detection function detects the magnetic polarity and stores the phase data in the ServoPack relative to the linear scale. This detection routine is initiated automatically the first time a ServoON command is received from the host controller after initial power up of the servo system. Attachments: 238KB Product Group/Line: Servo Products, SGLF Series, SGLG Series, SGLT Series, Sigma Trac, SGT Sigma Trac, STF Sigma Trac, SGDV Analog, SGDV EtherCAT, SGDV MECHATROLINK-II, SGDV MECHATROLINK-III, SGDV MP2600iec, SGDV SigmaLogic Topic/Sub Topic: Ask a Technical Question, Adjustments, Alarm, Application Example, Applications, Hardware, Procedure - Policy, Instructions, Integration, Options, Parameters, Programming, Start Up - Installation, Training, Troubleshooting, Tuning, Wiring, EMI - RFI Document Number: MTN-9GATY7 Published Date: 03/12/2024	03/12/2024
How are the Electronic Gear Ratio parameters, Pn202 and Pn203, set for linear motors? Posted Date: 07/25/2005 Answer: The positioning resolution of the linear motor when used with the Sigma II SGDH servo amplifier in position mode is equal to the linear encoder scale pitch divided by 256. For a 20 micron pitch linear encoder (i.e. Renishaw RGH22B), the positioning resolution is 20 micron/256. The incoming position reference is scaled by the Electronic Gear Ratio. Pn202 is the Electronic Gear Ratio numerator, set to a default of 4. Pn203 is the Electronic Gear Ratio denominator, set to a default of "1". Therefore, with these these default settings, for every reference input pulse, the linear motor will move (4/1) x (20 microns/256) or 0.3125 microns, assuming a 20 micron pitch linear encoder. The Electronic Gear Ratio can be changed to allow for "friendlier" positioning units. For example, assuming a 20 micron pitch linear encoder: 1.) The desired position reference resolution is one micron (or 0.001mm). For every reference pulse, the linear motor moves one micron. To achieve this resolution, set Pn202=256 and Pn203=20. Now, for every reference pulse, the linear motor will move (256/20) x (20 microns/256) or one micron. 2.) The desired position reference resolution is 0.001 inch. Set Pn202=8128 and Pn203=25. Now for every reference pulse, the linear motor will move (8128/25) x (20 microns/256) x (25.4 inches/0.001mm), which is equal to 0.001 inch. Product Group/Line: Servo Products, SGDH Sigma II, SGLF Series, SGLG Series, SGLT Series Topic/Sub Topic: Ask a Technical Question, Programming, Start Up - Installation Document Number: PZAC-5MHK9X Published Date: 07/25/2005	07/25/2005
Can the linear encoder be mounted "backwards" (positive direction of linear encoder opposite to positive direction of linear motor)? Posted Date: 04/28/2003 Answer: Yes, the linear encoder can be mounted "backwards" relative to the linear motor, it is good design practice to insure that the motor and encoder have the same positive direction reference. Normally, the linear motor and encoder would be oriented such that the positive direction of each is in the same direction. The positive direction of the linear motor is in the direction in which the motor cables/connectors protrude. Generally, this holds true for the linear encoder as well (as it does for Renishaw and Heidenhain). Please consult the linear encoder manufacturer in regards to positive orientation. If the linear encoder is mounted "backwards" relative to the linear motor, one of the following MUST be done in order for the linear motor system to function properly. 1. Rewire the linear encoder cable. Swap the "A" signal wires with the corresponding "B" signal wires. 2. The following is only applicable for Sigma II SGDH type servo amplifiers with the Y213 modification (Y213 modification is for use with linear motors only). Set user parameter Pn080.1=1 (B-phase progression). This will allow for proper commutation of the linear motor. However, the positive direction of the motor will now be in the direction opposite in which the motor cables/connectors protrude. To change the motor direction, set Pn000.0=1. 3. The following is only applicable for Legend SGDG type servo amplifiers. Set SW1 function selection switch no.4 (Linear Scale Polarity Reversal) to OFF (B-phase progression). This will allow for proper commutation of the linear motor. However, the positive direction of the motor will now be in the direction opposite in which the motor cables/connectors protrude. To change the motor direction, set SW1 function selection switch no.6 (Feedback Pulse B-phase Reversal) to OFF. Product Group/Line: Servo Products, SGDG LEGEND, SGDH Sigma II, SGLF Series, SGLG Series, SGLT Series Topic/Sub Topic: Ask a Technical Question, Programming, Start Up - Installation Document Number: PZAC-5M2RXT Published Date: 04/28/2003	04/28/2003
Are there any integration tips available for Linear Motors? Posted Date: 07/13/2004 Answer: Yes. In order to successfully integrate Linear Motors into automated machinery, there are several considerations that have to be taken into account. Material selection, mechanical precision, bearing force and life expectancy, thermal considerations, magnet track considerations, stroke length, environmental considerations, feedback system are important factors to realize before integrating Linear Motors into machines. The attached document provides integration tips for successful utilization of Linear Motors. Attachments: 1.2MB Product Group/Line: Servo Products, SGLF Series, SGLG Series, SGLT Series Topic/Sub Topic: Ask a Technical Question, Integration Document Number: REKR-5JWR4M Published Date: 07/13/2004	07/13/2004

Showing 1 to 16 of 16 entries.

SAFETY PRECAUTIONS AND INSTRUCTIONS FOR USE OF FAQ INFORMATION!

Please read and understand the product instruction manual before installing, servicing or operating Yaskawa products. FAQ content and illustrations are provided as technical advice to augment the information in manual, not supersede it. It is not possible to give detailed instructions for all types of installation or support activities. The information described in the FAQs are subject to change without notice to improve the product or FAQ. Yaskawa assumes no responsibility for errors or omissions or damages resulting from the use of the information contained in any FAQ. All warnings, cautions and product instruction for product use must be followed. Installation, operation and maintenance should be carried out by qualified personnel. Failure to observe these and other precautions highlighted in the product manuals will expose the user to high voltages resulting in, serious injury or death. Qualified personnel are defined as individuals who are familiar with the installation, starting, operation and maintenance of Yaskawa products of the type described and have proper qualifications to perform the work.

Node: dxpprd01:80

SiteSearch

Yaskawa Main Navigation

SGLF Series

EditContent

Navigation Menu

SGLF Series

SGLF Series

SGLF Series - Sigma-5 - YAIMOB

Iron-core coil and magnet track components

TemplateWeb

Overview

Software

Support & Training

Documents

Drawings

FAQs

SAFETY PRECAUTIONS AND INSTRUCTIONS FOR USE OF FAQ INFORMATION!

SiteSearch

Americas

Europe/Africa/Middle East

Japan/Asia/Pacific Rim

SiteSearch

SGLF Series

Breadcrumb

Navigation Menu

SGLF Series

SGLF Series

SGLF Series - Sigma-5 - YAIMOB

Iron-core coil and magnet track components

TemplateWeb

Overview

Software

Support & Training

Documents

Drawings

Overview

Software

Support & Training

Documents

Drawings

FAQs

SAFETY PRECAUTIONS AND INSTRUCTIONS FOR USE OF FAQ INFORMATION!

SiteSearch