SMC-3010 LEGEND-MC

SMC-3010 LEGEND-MC - YAI

Single-axis motion controller

The SMC-3010 LEGEND-MC is a legacy product and no longer promoted in the Americas. The SMC-3010 series was a single-axis machine controller with Ethernet communcation that attached to any Yaskawa LEGEND amplifier. Featured 100% digital design, multi-axis control via software, dual programming screens, and high performance and reliability.

User Manual

TemplateWeb

FAQs

Sort by :

Expand All

Didn't find what you were looking for? Try solutioncenter.yaskawa.com

Showing 421 to 430 of 1,000 entries.

Previous Page
Page1
Intermediate Pages
- Page2
- Page3
- Page4
- Page5
- Page6
- Page7
- Page8
- Page9
- Page10
- Page11
- Page12
- Page13
- Page14
- Page15
- Page16
- Page17
- Page18
- Page19
Page42
Page43
Page44
Intermediate Pages
- Page45
- Page46
- Page47
- Page48
- Page49
- Page50
- Page51
- Page52
- Page53
- Page54
- Page55
- Page56
- Page57
- Page58
- Page59
- Page60
- Page61
- Page62
- Page63
- Page64
Page100
Next Page

Question	Posted Date
The MotionWorks IEC Hardware Configuration software is unable to connect to the MPiec controller. What should I check to correct the problem? Posted Date: 09/23/2013 Answer: Please see the attached PDF for a detailed explanation. Attachments: 446KB Product Group/Line: Controllers, MotionWorks IEC Topic/Sub Topic: Ask a Technical Question, Software Document Number: MTN-9AJMA2 Published Date: 09/23/2013 Share \| Rate Rate this article :	09/23/2013
The J7 drive will only allow the parameter to viewed but not changed.What must be done to change parameter values in the J7/305 AC drive? Posted Date: 06/11/2014 Answer: See attached. Attachments: 44KB Product Group/Line: Inverter Drives, J7 Drive Topic/Sub Topic: Ask a Technical Question, Programming, Start Up, Troubleshooting Document Number: DRV-5GSUDM Published Date: 06/11/2014 Share \| Rate Rate this article :	06/11/2014
The HV600 is described as a fan and pump drive. Is there new pump control functionality built into the drive? Posted Date: 09/03/2019 Answer: Yes. Several new pump-specific control functions come as standard to provide easy setup, save energy costs, and help assure pump protection. Product Group/Line: Inverter Drives, HV600 Drive Topic/Sub Topic: Ask a Technical Question, Product Launch Document Number: INV-E0E1V4 Published Date: 09/03/2019 Share \| Rate Rate this article :	09/03/2019
The Hardware Configuration launches, but does not appear after using dual displays, is there a way to reset its position? Posted Date: 08/04/2014 Answer: Yes. Please see the attached document. Attachments: 245KB Product Group/Line: Controllers, MotionWorks IEC, MP2000iec Series, MP2300Siec, MP2310iec, MP2600iec, MP3200iec Topic/Sub Topic: Ask a Technical Question, Adjustments, Environment, Operation, Programming, Troubleshooting Document Number: MTN-9GRS4X Published Date: 08/04/2014 Share \| Rate Rate this article :	08/04/2014
The GUI displays mm. How can it change to inches? Posted Date: 07/23/2021 Answer: To change the units used in the Position Display navigate to the Machine Configuration page, drop down cartesian axes, check the box for Override and choose your preferred units to be used in the Position Display. To change the units of your commands in a G Code file you can either execute a G20 (set commands to be in inches) or a G21 (set commands to be in mm). It is common that a G Code file will specify G20 or G21 at the beginning of the file. Product Group/Line: Yaskawa Compass, Controllers Topic/Sub Topic: Ask a Technical Question Document Number: CNT-8C92Q8 Published Date: 07/23/2021 Share \| Rate Rate this article :	07/23/2021
The GPD 515/G5 displays a parameter, but does not let me change it. Why? Posted Date: 07/13/2004 Answer: Parameter A1-01 controls access to all parameters that are available in the control method being used. A setting of 'Advanced' allows all of the available parameters of the current control method to be changed. Some parameters are not available in some control methods. Refer to Appendix 1 in the technical manual. Product Group/Line: Inverter Drives, G5 GPD515 Drive, G5 Drive 600 Volt Topic/Sub Topic: Ask a Technical Question, Troubleshooting, Programming Document Number: DRV-5FLM9Y Published Date: 07/13/2004 Share \| Rate Rate this article :	07/13/2004
The GPD/515G5 instruction manual (TOE-S616-10.13) (pages 21-22) specifies that input fuses should be used on the installation of these drives.--Is fusing required or is a circuit breaker sufficient protection for the inverter?--If fusing is not required, what characteristics of MCCB should used be to protect the drive adequately? Posted Date: 06/08/2007 Answer: In the U.S., two types of branch circuit protection are required by local and national codes, branch circuit overload protection and branch circuit short-circuit protection. This protection is necessary to protect the circuit feeding the device (mainly input wiring). See attached for full details. Attachments: 17KB Product Group/Line: Inverter Drives, G5 GPD515 Drive, G5 Drive 600 Volt Topic/Sub Topic: Ask a Technical Question, Circuit Protection Document Number: DRV-5T6SRU Published Date: 06/08/2007 Share \| Rate Rate this article :	06/08/2007
The E7L will not run the motor in Hand or Auto mode. What can cause this? Posted Date: 10/27/2005 Answer: Possible Solution: 1. The ribbon cable UWR00562-1 may be partially plugged or loose between Electronic Bypass Keypad (A3) and Electronic Bypass Control PCB (A2). Attempt to reseat or push the ribbon connector in as needed on one, or both ends to correct this problem. (See attachment.) Other symptoms of this problem include: 1. Drive LED flashes. 2. Stop LED is lit. 3. Contol Power LED is lit. 4. No Ready LED. Refer to TM.E7L.01 the E7L Drive Bypass Technical Manual for more information. Attachments: 97KB Product Group/Line: Inverter Drives, E7L Drive Bypass Topic/Sub Topic: Ask a Technical Question, Operation, Start Up, Troubleshooting Document Number: DRV-5VWPB6 Published Date: 10/27/2005 Share \| Rate Rate this article :	10/27/2005
The E7 drive inside the bypass enclosure unit doesn't have the Hand, Off or Auto buttons that are shown in the E7 manual. How can the drive be run locally? Posted Date: 07/13/2004 Answer: To limit confusion, the Hand, Auto and Off buttons on the keypad were disabled and a membrane/sticker was placed over the buttons on the face of the keypad. This is done only on units that have a seperate H-O-A switch on the door of the enclosure.These functions can only be accessed manually, by adjusting the Hand/Off/Auto switch located on the front panel of the bypass unit. They are peripheral methods for changing operation methods. The purpose for this is to limit confusion by having only one Hand/Off/Auto control. Product Group/Line: Inverter Drives, E7B Drive Bypass Topic/Sub Topic: Ask a Technical Question, Bypass Function, Keypad-Operator, Programming, Start Up Document Number: DRV-5GRV4D Published Date: 07/13/2004 Share \| Rate Rate this article :	07/13/2004
The E7B bypass unit with the serial communications, option J or option L control comes set up for the start/stop as well as the speed reference to be controlled through serial communication. Is it possible to maintain start/stop control through serial communication while using an analog signal for speed reference? Posted Date: 06/11/2014 Answer: See attached. Attachments: 18KB Product Group/Line: Inverter Drives, E7B Drive Bypass Topic/Sub Topic: Ask a Technical Question, Bypass Function, Networks, Programming Document Number: DRV-5GZPRR Published Date: 06/11/2014 Share \| Rate Rate this article :	06/11/2014

Showing 421 to 430 of 1,000 entries.

Previous Page
Page1
Intermediate Pages
- Page2
- Page3
- Page4
- Page5
- Page6
- Page7
- Page8
- Page9
- Page10
- Page11
- Page12
- Page13
- Page14
- Page15
- Page16
- Page17
- Page18
- Page19
Page42
Page43
Page44
Intermediate Pages
- Page45
- Page46
- Page47
- Page48
- Page49
- Page50
- Page51
- Page52
- Page53
- Page54
- Page55
- Page56
- Page57
- Page58
- Page59
- Page60
- Page61
- Page62
- Page63
- Page64
Page100
Next Page

SAFETY PRECAUTIONS AND INSTRUCTIONS FOR USE OF FAQ INFORMATION!

Please read and understand the product instruction manual before installing, servicing or operating Yaskawa products. FAQ content and illustrations are provided as technical advice to augment the information in manual, not supersede it. It is not possible to give detailed instructions for all types of installation or support activities. The information described in the FAQs are subject to change without notice to improve the product or FAQ. Yaskawa assumes no responsibility for errors or omissions or damages resulting from the use of the information contained in any FAQ. All warnings, cautions and product instruction for product use must be followed. Installation, operation and maintenance should be carried out by qualified personnel. Failure to observe these and other precautions highlighted in the product manuals will expose the user to high voltages resulting in, serious injury or death. Qualified personnel are defined as individuals who are familiar with the installation, starting, operation and maintenance of Yaskawa products of the type described and have proper qualifications to perform the work.

Node: dxpprd02:8080

Rating

Rate

SiteSearch

Yaskawa Main Navigation