SGM7E Direct Drive
Breadcrumb
Navigation Menu
SGM7E Direct Drive
SGM7E Direct Drive
SGM7E-Direct-Drive - YAIMOB
Up to 105Nm peak torque
The SGM7E servomotor line is designed for direct drive applications where the load is directly attached to the motor surface. Pre-tapped mounting holes and a hollow-through shaft permit a variety of machine designs. This direct drive motor has substantial load carrying bearings, low speed windings, and 24-bit absolute encoders that allow for highly accurate indexing. 200 volt windings are available with maximum speeds up to 500 rpm. There are 11 sizes available with up to 105Nm peak torque.
TemplateWeb
eLearning Curriculum
Showing 1 to 20 of 20 entries.
Title/Number | File(s) | Rev Date | |
---|---|---|---|
eLearning Module: Servo Motor Sizing Basics Part 1 - Core Concepts eLM.Servo.02.Sizing1 39.9MBRev Date:10/30/2017 Watch Video
|
39.9MB
|
10/30/2017 | |
eLearning Module: Servo Motor Sizing Basics Part 2 - Technical eLM.Servo.03.Sizing2 41.1MBRev Date:07/30/2019 Watch Video
|
41.1MB
|
07/30/2019 | |
eLearning Module: SigmaSelect Overview eLM.Servo.04.Sizing_Overview 38.1MBRev Date:10/02/2019 Watch Video
|
38.1MB
|
10/02/2019 | |
eLearning Module: Servo Sizing Rotary Table eLM.Servo.05.Sizing_ROT_TBL 42.4MBRev Date:10/02/2019 Watch Video
|
42.4MB
|
10/02/2019 | |
eLearning Module: Servo Sizing Linear Ballscrew eLM.Servo.06.Sizing_BALLSCRW 61.4MBRev Date:10/02/2019 Watch Video
|
61.4MB
|
10/02/2019 | |
eLearning Module: Servo Sizing Roll Feeder eLM.Servo.07.Sizing ROL_FED 54.2MBRev Date:10/02/2019 Watch Video
|
54.2MB
|
10/02/2019 | |
eLearning Module: Sigma-7 Features and Benefits eLM.Sigma-7.01.Feat_Benefits 225.1MBRev Date:06/07/2016 Watch Video
|
225.1MB
|
06/07/2016 | |
eLearining Video: Direct Drive Servos eLV.DirectDrive.01.TechIntro 159.4MBRev Date:10/21/2021 Watch Video
|
159.4MB
|
10/21/2021 | |
eLearining Video: Yaskawa Direct Drive Motors eLV.DirectDrive.02.ProductLine 130.9MBRev Date:09/03/2021 Watch Video
|
130.9MB
|
09/03/2021 | |
eLearining Video: Servo Sizing Demystified eLV.Servo.01.SizDemystify 186.2MBRev Date:04/20/2021 Watch Video
|
186.2MB
|
04/20/2021 | |
eLearning Video: Servo Basic Concepts - Homing eLV.ServoMotion.08.SBC_Homing 14.3MBRev Date:04/02/2014 Watch Video
|
14.3MB
|
04/02/2014 | |
eLearning Video: Servo Basic Concepts - Actuators eLV.ServoMotion.09.SBC_Actuators 11.6MBRev Date:04/02/2014 Watch Video
|
11.6MB
|
04/02/2014 | |
eLearning Video: Servo Tuning - Stop High Pitched Sounds eLV.Sigma7.01.Notch 47.8MBRev Date:01/13/2022 Watch Video
|
47.8MB
|
01/13/2022 | |
eLearning Video: Sigma-7 Startup eLV.Sigma7.01.Startup 84.1MBRev Date:03/01/2021 Watch Video
|
84.1MB
|
03/01/2021 | |
eLearning Video: Servo Tuning - Stop Resonant Sounds eLV.Sigma7.02.AntiRes 44.0MBRev Date:01/18/2022 Watch Video
|
44.0MB
|
01/18/2022 | |
eLearning Video: Servo Tuning - Suppress Load Vibration eLV.Sigma7.03.VibSup 83.3MBRev Date:01/13/2022 Watch Video
|
83.3MB
|
01/13/2022 | |
eLearning Video: Servo Tuning - Suppress Two Vibration Frequencies eLV.Sigma7.04.VibSup2Freq 42.0MBRev Date:01/18/2022 Watch Video
|
42.0MB
|
01/18/2022 | |
eLearning Video: Servo Tuning - Minimize Settling Time eLV.Sigma7.05.SettlingTime 67.3MBRev Date:01/18/2022 Watch Video
|
67.3MB
|
01/18/2022 | |
eLearning Video: Servo Tuning - Minimize Position Error eLV.Sigma7.06.PosError 66.7MBRev Date:01/18/2022 Watch Video
|
66.7MB
|
01/18/2022 | |
eLearning Video: Servo Tuning - Estimate High Inertia Loads eLV.Sigma7.07.DDJcalc 57.1MBRev Date:06/24/2022 Watch Video
|
57.1MB
|
06/24/2022 | |
Showing 1 to 20 of 20 entries.